Skip to content
Richardson Plumbing Solutions (877) 721-3626
03

Faucet Repair in Richardson, TX

We repair drips, leaks, loose handles, and low-flow faucets in Richardson.

A plumber crouching at an outdoor shut-off on the side of a house, a red pipe wrench on the galvanised pipe below a brass gate valve, an open service van behind him

A steady tap heard from the hallway and a wet cabinet floor are often both called a faucet leak, but they point to different faults. Water falling from the spout after the handle is off usually involves the cartridge, stem seal, or valve seat inside the faucet body. Water at the sink base, countertop, or cabinet may come from a loose mounting nut, worn supply connection, spray hose, or failed seal. We trace both paths rather than treating every drip as the same repair.

Kitchen, bathroom, laundry, and bar-sink fixtures can also lose flow without leaking, especially when an aerator screen catches scale or a handle no longer opens a valve fully. We work on the visible fixture, its shutoff valves, supply tubes, handle, spout, and connections under the sink. A slow spout drip can generally be scheduled before it wastes more water, but an active leak below the counter should not wait because water can swell a cabinet bottom, soak drywall, and reach flooring.

Dripping spout and loose handle

A faucet that will not stop dripping usually means water is passing through the valve after the handle is closed. A loose handle that spins, slips, or only works in one position can point to a worn cartridge stem, handle adapter, set screw, or internal stop. Customers also call about low water pressure at one sink when the shower and other fixtures have normal flow, which often narrows the check to the aerator, supply stops, or faucet passages. Water under the sink only while the faucet runs can come from a pull-down hose, a supply tube, or the faucet base rather than the spout.

White mineral buildup around the aerator and a stream that sprays sideways can be a screen or outlet problem, while a drip from the tip is usually farther inside the valve body. We inspect the fixture before choosing a cartridge, washer, hose, or mounting repair. Separate faults can look alike from the counter, yet each needs different parts and access, so the repair cost can vary after the faucet is opened.

Fixture inspection and cartridge test

During a fixture inspection, we identify the faucet make, examine the handle travel, and isolate the hot and cold shutoff valves under the sink. We check the supply tubes, mounting hardware, spout base, pull-out hose, spray head, and aerator for the actual source of water or restricted flow. A pressure gauge can help confirm whether the faucet problem is local when household supply pressure is normally within the 40 to 80 psi range. We also run hot and cold water separately to see whether the fault follows one side of the mixer.

A straightforward inspection and an aerator, cartridge, washer, or handle repair commonly take 30 to 60 minutes when the shutoffs operate and the needed part is available. We can usually complete accessible internal repairs during the same visit after the faucet body is opened and the failed component is identified. A seized stop valve, corroded mounting nut, cracked faucet body, or cartridge that must be ordered can require a return visit. We explain whether the fixture can be rebuilt, needs a specific replacement part, or has damage that makes replacement more practical.

Cartridge age and seized shutoffs

An older cartridge may be discontinued, swollen with mineral scale, or difficult to remove from the valve body, especially when the faucet has seen years of hard-water buildup. Access also changes the scope of a repair: a wide cabinet with clear shutoff valves is different from a tight vanity with a garbage bin, shelf, or fixed panel in the way. A shutoff valve that will not close can add work because the water supply must be controlled before the faucet is opened.

A standard cartridge or aerator can often be fitted once the make and model are known, while a specialty stem, ceramic valve, finish-specific handle, or pull-down hose may have to be ordered. Corrosion at the mounting plate or supply connection can make a simple handle or spout complaint involve more disassembly beneath the sink. Like-for-like internal faucet work is different from changes to piping or commercial fixtures that may need property approval or local sign-off.

Model number and cabinet access

Before calling, check which room contains the faucet and whether the issue is at the kitchen sink, bathroom vanity, laundry sink, or bar sink. Look for the brand name on the handle cap, spout, spray head, or escutcheon plate, and note any model number printed on the installation guide or beneath the fixture body. Tell us whether water is dripping now, leaking only when the faucet runs, or appearing inside the cabinet after use.

Clear a path to the cabinet doors and mention any shelf, disposal unit, or panel blocking the shutoff valves and supply tubes. An approximate installation age can help when the faucet uses an older cartridge or discontinued handle connection. Call us at (877) 721-3626 before water beneath the sink swells the cabinet base or damages the flooring around the fixture.

When we are open

Mon–Sun Open 24 hours

Next