Gas Line Repair in Richardson, TX
Gas line checks and repairs for leaks, valves, fittings, and appliance connections.
Homeowners and tenants call us saying, “I smell rotten eggs by the stove,” “there is a hiss behind the dryer,” or “the gas fireplace will not stay on.” Those phrases usually point to a possible issue with odorized natural gas, a connector, a shutoff valve, a pipe joint, or an appliance supply line. We trace the symptom back to the gas component instead of assuming the appliance is the source.
Other callers notice a gas smell in a cabinet, near a water heater, or outside by the meter area. A burner that will not light, a pilot that goes out, or a flexible connector that looks bent or corroded can also lead to a gas line inspection. We check the line route, fittings, valves, and accessible connections to identify where gas may be escaping or failing to reach an appliance.
A gas odor, hissing sound, or suspected leak should not wait because escaping gas can collect in a room, cabinet, wall cavity, or crawl space. Avoid flames, smoking materials, and electrical switches near a suspected leak, and leave the area if the odor is strong. Gas line repair needs prompt attention because the hazard is tied to the fuel supply, not merely to a fixture that has stopped working.
Rotten egg smell and hissing
A rotten egg smell near a stove, dryer, furnace, fireplace, or water heater is one of the most common reasons customers call about a gas line. A steady hiss at a valve, behind an appliance, or along exposed pipe can indicate gas moving through a damaged fitting or loose joint. Gas odor outdoors near a meter, riser, or exterior wall can also need investigation, especially when the smell remains in one area.
Some callers report that a gas burner will not light, a fireplace pilot goes out, or an appliance shuts down after starting. A yellow or weak burner flame can involve the appliance itself, while a failed shutoff valve or restricted supply line can affect gas delivery before it reaches the burner. A leaking connector, a faulty appliance control, and a seized valve can sound similar over the phone, but each fault involves different parts and different repair work.
Gas line inspection and pressure test
During a gas line inspection, we examine accessible pipe, threaded joints, flexible connectors, appliance valves, and the shutoff serving the affected fixture. We use a gas detector and leak-testing solution around suspect connections, then check supply pressure with a manometer where testing is appropriate. Natural-gas appliance supply commonly operates near 7 inches of water column, although the required pressure test and hold time depend on the piping layout and local requirements.
An initial inspection and accessible leak check often takes 30 to 60 minutes, with additional time needed when pipe runs pass through walls, ceilings, cabinets, attics, or crawl spaces. We can often replace an accessible connector, fitting, or shutoff valve during the visit when the correct approved part is available. Concealed pipe replacement, a changed gas route, permit work, or a required inspection is normally scheduled separately because the wall opening, pipe installation, and sign-off may need coordination.
Pipe route, shutoff, and fittings
Gas line repair cost changes with the pipe route, the condition of the shutoff valve, and the type of fitting at the leak. An exposed connector behind a range is generally simpler to reach than a joint inside a wall, above a ceiling, or beneath a raised floor. Older steel pipe, corroded threads, and fittings that no longer separate cleanly can add removal and replacement work.
A shutoff valve that has seized may require more than a minor adjustment because the valve body, pipe connection, and appliance supply line may all need attention. Parts that match the pipe material, connector size, and appliance connection can affect whether repair work is completed during the visit or requires an ordered component. Permit requirements, utility coordination, and inspection sign-off can also add steps when the repair changes piping rather than replacing an accessible connection.
Appliance plate and shutoff location
Before calling, check the appliance model number and serial number on the rating plate, which is often inside a furnace panel, behind a range drawer, or on the side of a water heater. Tell us which room contains the appliance and whether the odor or hissing is at the stove, dryer, fireplace, furnace, or water heater. Note whether the appliance is currently running, whether a burner lights, and whether the gas smell is indoors or outdoors.
Let us know where the shutoff valve, crawl-space entry, attic access, or cabinet opening is located so we can plan for the pipe route. A photo of an exposed connector, valve, or corroded fitting can help identify the likely connection type before the visit. Call (877) 721-3626 because a leaking joint can continue releasing gas into a cabinet, wall cavity, or room while repair work waits.
When we are open
Mon–Sun Open 24 hours
Next
Next: water softener installation, or back to the home page.
